UA-75297209-1 STV Eliminator
STV Eliminator

STV Eliminator

review
5
0
5
Your Price: $89.99
Part Number:STVE-

Choose Options

Select Kit (see application guide):

Due to emission and noise control regulations secondary throttle valves appeared in motorcycles in the last decade. This secondary butterfly is controlled by the bike’s ECU. For maximum performance and crisp throttle response this secondary system is removed – mainly in drag racing / road racing. However, as soon as you disconnect the secondary throttle valve actuator motor from the bike’s main wiring harness, the FI light will come on on the instrument panel. The STV Eliminator plugs into the bike’s wiring loom directly. With the help of this small unit, you’re able to remove the whole secondary valve assembly with the actuator motor, the butterfly valve plates and the rod/shaft too. Get the job done properly with this easy fix!

Note: After installation, we recommend having the AFR (air-fuel ratio) of the engine checked by a dyno center and adjust if necessary.


PLUG-N-GO DESIGN

The Plug ‘n Go connector makes installation quick and easy, eliminating the need to alter the bike’s original wiring.


PROPER SOLUTION TO YOUR PROBLEM

Eliminates the FI light coming on when disconnecting the electronic actuator motor / removing the secondary butterfly valve(s) from the bike. This is a must have piece of kit for racers!


ADVANCED TECH

The unit is completely sealed and epoxy encapsulated, which gives extreme protection for the internal parts from shocks, vibrations and water.


Quick and simple to use:
Just disconnect the actuator motor from the main wiring harness. Plug in the STV Eliminator and the unit will act as the actuator motor would still be in place. No splicing or soldering required and the bike’s wiring harness remains intact. It can’t get any easier than this!

Lower-cost alternative:
If the actuator motor fails (frequent issue on some bike models) it is much cheaper to replace it with the STVE than getting a new motor.


Light and small:
The STVE module is about the same size as the actuator motor it replaces.


Built to last:
Rugged design, encased in epoxy resin. Only high-quality SMD components used. Each unit is extensively tested prior to shipping. Oil and water resistant (IP68).


APPLICATION GUIDE:


STVE-01
SUZUKI B-King (2008-2012), Boulevard C50 (2005-2019), Boulevard M50 (2005-2019), Boulevard C90 (2005-2019), Boulevard M90 (2009-2019), DL1000 V-Strom (2014-2017), GSX1300R Hayabusa (2008-2019), GSX-R1000 (2005-2008), Intruder C800 (2005-2017), Intruder M800 (2005-2015), Intruder C1500 (2005-2017), Intruder M1500 (2009-2015), VL800 Intruder Volusia (2001-2019), VL1500 Intruder (1998-2017), VZ800 Marauder (2005-2015), VZ1500 (2009-2015)


STVE-02 

KAWASAKI Ninja 250R [FI model] (2008-2017), Ninja 300 (2013-2018), Ninja 650 (2017-2019), Versys 650 (2015-2019), Vulcan S 650 (2015-2019), Z300 (2015-2016), Z400 (2018), Z650 (2017-2019) SUZUKI AN400 Burgman (2007-2018), GSX-R1000 (2009-2016) 


STVE-03 

SUZUKI GSF1250 N/NA Bandit (2007-2013), GSF1250 S/SA Bandit (2007-2016) 


STVE-04 

SUZUKI GSX-R600 (2006-2009), GSX-R750 (2006-2009)


STVE-06 

KAWASAKI 1400GTR (2008-2019), Concours 14 (2008-2019), ZG1400 Concours (2008-2019), ZX-10R Ninja (2006-2007), ZX-14 (2006-2019), ZZR1400 (2006-2019) 

SUZUKI Boulevard C109R/T (2008-2015), Boulevard M109R/R2 (2006-2019), Gladius (2009-2015), GSR600 (ALL years), GSR750 (2011-2017), GSX650F (2008-2015), GSX1250FA (2010-2017), GSX-R600 (2004-2005), GSX-R600 (2010-2017), GSX-R750 (2004-2005), GSX-R750 (2010-2017), GSX-S750 (2015-2019), GSX-S750Z (2018-2019), GSX-S1000 /F /A /FA (2015-2016), Intruder C1800R (2008-2015), Intruder M1800R (2006-2019), SFV650 (2009-2015), SV650 (2017-2019), SV650X (2018-2019), VLR1800 (2008-2015), VZR1800 (2006-2019)


STVE-07 

KAWASAKI Versys 1000 (2012-2019), W800 (2011-2019), Z750 (2004-2012), Z750R (2011-2012), Z800 (2013-2017), Z800e (2013-2017), Z900 (2017-2019), Z900RS (2018-2019), Z1000 (2003-2019), Z1000SX (2011-2019), ZX-10R Ninja (2008-2015), ZX-12R Ninja (2002-2006) 


STVE-08 

KAWASAKI ZX-6R Ninja (2004-2019)

5 Stars
Simple product for a simple problem
I removed my secondary throttle assembly and the FI light (understandably) came on with the STVA error code. Installed the STV Eliminator in 2 minutes and the FI light is now off. I appreciate that it comes with adhesive velcro to mount it easily. The STVE is also fairly small, wasn't hard to find a spot to mount it.
Did you find this helpful? 
Reviewed by:  from Canada. on 6/4/2019
5

Recently Viewed Items